KOBALT Active - Pair

KOBALT

The BI-PortTM and the ISO-RailsTM

The BI-PortTM was specially designed to keep the cabinet dimensions as small as possible, while supporting the High frequency section.

Therefore, we integrate the 25mm Neodymium Tweeter in the center of the BI-PortTM (Bass Reflex System) for two reasons; To aim for an efficient air cooling of the tweeter by the woofers air flow, secondly, and most importantly, to generate a "velocity field (ring shape)" around the tweeter to support its high frequency dispersion pattern over long distances! (riding on along the wave) Result - an unbelievably precise stereo image.

Also the ISO-RailsTM are features which have practical aspects as well as acoustical ones! Most available cabinets have flat surfaces; as a result, such speakers have a hard time staying in one location, especially when they are pushed hard, manually or by the force of the Woofer!

Not with the KOBALTs! The cabinet is standing on the ISO-RailsTM,- a special silicon profile - only. So there is no coupling to surface underneath nor is there any "slip" behavior going on, so the low end is always tight all the time!

As always with EMES, matched high quality drivers are chosen, because they are the most critical part in a quality Studio Monitor System!

The Low range (62 - 2000Hz) is reproduced by a 14cm polypropylene membrane HDS driver. A 25mm high efficiency Neodymium Tweeter located in the BI-PortTM is used from 2 - 20 kHz!

We, at EMES, always use identical amplifiers in order to have the lowest time related distortion possible! Therefore, two identical built-in 70W rms amplifiers, which deliver a powerful and optimized output, drive a single KOBALT Monitor. This is one of the many design criteria's we require to accomplish the EMES standard of audio performance.

To adjust the monitor to your personal listening level, a 16 position dip-switch has been added!

We ship the KOBALTs, like all other EMES monitors, as matched pairs!

Listening distance: 60cm - 250cm. (2 - 8 feet)

System KOBALT
Construction 2 way bass-reflex
Const./Speaker configuration One + One
Lower cut off frequency 62 Hz (-3dB)
Upper cut off frequency 20 kHz (-2dB)
fc response free field 64 - 20000 Hz +/- 3db
Maximum output, sine wave (0,1-2 kHz) 106 dB
Maximum output, long term, (RMS) 103 dB
Maximum output, both speakers driven 112 dB
THD at 95dB SPL <100Hz 1,10%
THD at 95dB SPL >100Hz 0,60%
Bass driver 1 x 14cm , polyprophylen
Hf driver 25mm textile dome, Ferrofluid
shielded (anti magnetic) Yes
weight 12.5 lbs
dimensions w/h/d in mm 10.75" x 6.75" x 10"
pair difference +/-0.5 dB
Electronic KOBALT
Type of input connector XLR, female - 6,3mm phone jack
input impedance 10 kOhm
input level adjustment 16 steps, from 0.45 - 4.5V
low pass filter 40 Hz/-18dB
high pass filter 25 kHz / 6 dB
X-over frequency 2.000 Hz (12dB/12dB)
RMS output Bass-amp 70 W
RMS output HF-amp 70 W
Distortion at maximum acoustic output 0,10%
Signal to noise ratio, at full output 106 dB
Main voltage 115 / 230 V +/-20%
Type of Power supply digital
Power consumption (full output) 120 W, 10 W stand by

used for:

• RECORDING
• BROADCAST
• FILM/VIDEO Editing
• PROJECT STUDIO

MAP (Minimum Advertised Price) in force. CALL!